Daly 72V 24S LiFePO4 BMS (120A-150A-200A-300A)

Special Price $75.00 Regular Price $95.00
In stock
SKU
24S-LFP-120-500-BMS
Size Chart
Need Help?
Contact Us
ô‿ô
Welcome

Daly 72V 24S LiFePO4 BMS BMS is also used in our battery pack. Their quality and performance are approved

Specification

 

Description Specification (LiFePO4-24S)
120A 150A 200A 250A 300A 400A 500A 600A
Discharge Continue discharge current 120A 150A 200 250 300A 400A 500A 600A
Sparkle current 400A±100 500A±100 600A±100 600A±100 1000A±200 [ 1200A±200 1500A±200| 1500A±200
Internal Resistance Main Circuit Conduct Innerresistance ≤20mQ ≤20mQ <20mQ 20mQ ≤20mQ <20mQ <20mQ ≤20mQ
Charge Standard Charge voltage DC87.6V
Charge current 60 75A 100A 125A 150A 200A 225A 225A
Over Charge Protection over charge detect voltage 3.75+0.05V
over charge protection delay 1S
lover charge release voltage 3.55+0.05V
Balance Balance detect Voltage 3.5V
Balance release voltage 3.5V
Balance current 30±5mA
Over Discharge Protection Over discharge detect voltage 2.2土0.05V
over discharge detect delay 1S
Over discharge release voltage 2.7±0.05V
Over Current Protection over current detect voltage 1Ms
over current detect delay Off load
Short Circuit Protection Short Circuit protection condition Short circuit of external load
Short circuit detect delay 250uS  (J25B/25Ais960us)
Short circuit protection release condition Off load
Self Consumption Working current 100uA (80A & above is 500uA)
Sleeping current(when in discharge) o uA
Working Temperature Temp range  -20~70℃
Storage Temperature Temp range  -40~80℃

Overview Of Daly BMS

BMS for LiFePO4

Application field

BMS connection Diagram

Daly BMS Connection Instructions:

1、PIease do not insert balance wires into BMS before connecting batteries, must make sure connecting
with batteries correctly.
II、The sequence of connecting wires for BMS:
Notes: Please ensure to use balancing wires from Daly BMS
1.Start from thin black balance wire, the 2nd wire(thin red wire) connect with the 1st battery's positive
pole. Then connect each cell's positive pole in order until the last one's positive B+.
2. Do not insert the connector directly after the wires were connected. Measure the voltage between two
adjacent metal terminals on the back of the connector. If it is Li-ion battery, the voltage should be bet-
ween 3.0 ~ 4.2V, Lifepo4 battery should be between 2.0 ~ 3.6V, and LTO battery should be between 1.5
~ 2.75V;
3.After the wiring sequence and voltage are confirmed to be correct, then insert into BMS.
4.Adjust the multimeter to the buzzer position and measure the internal resistance between B - and P-
when the internal resistance is 0, there will be a beep, which means that the BMS is good. Otherwise,
do not weld and contact the customer severice.
5.The last step to connect B-(thick blue wire) with battery pack's total negative pole.
III、After finished wiring:
Measure whether the B + and B-voltage and B + and P-voltage of the battery are equal, If yes, it means
the BMS works normally and can be used. If not, please recheck according to the above wiring sequence.
IV、If you have any other questions, pls contact us for support.

BMS Structure Breakdown

Product Feature

Product Feature 2

Daly BMS development History

0
Rating:
% of 100
Write Your Own Review
Only registered users can write reviews. Please Sign in or create an account